P501 Miniature Rotary Position Sensor

Description

The Positek P501 is a miniature, affordable, durable, high-accuracy rotary position sensor designed for industrial and scientific feedback applications, but requires a smaller footprint than the P500 rotary position sensor.

Like all Positek® sensors, the P501 miniature rotary position sensor provides a linear output proportional with angle of deflection. Each unit is supplied with the output calibrated to the angle required by the customer, between 30 and 140 degrees. It is particularly suitable for OEMs seeking good sensor performance for arduous applications where space is important.

Overall performance, repeatability and stability are outstanding over a wide temperature range. The Positek sensor has a rugged nickel plated aluminium body and integrated mounting flange. The flange has two 4.5mm by 20 degree wide slots on a 38mm pitch to simplify mounting and position adjustment. Sealing is to IP67 (boot version) and full EMC protection is built in.

As a leading designer and manufacturer of linear, rotary, tilt and intrinsically safe position sensors, Positek® has the expertise to supply a sensor to suit a wide variety of applications. We also have the LIPS® range for linear sensors, TIPS® for detecting tilt positions and RIPS® which is for rotary sensors such as the P501.

Follow us on Facebook

Positek offers a range of options for its standard sensors. Each sensor is manufactured to suit each customer's preferences. If your requirement is outside the options given below, Positek can modify/ redesign a sensor to suit your specific requirement. Standard options are available as below:

Measurement Range

Factory set to any length from ±15° to ±70° in increments of 1°. For example, if your application requires 90° measurement, then Positek will manufacture the sensor specifically for this angular range. The sensor will measure 90° however will still rotate through 360°.

Electronic Options

Output Signal	Supply Input	Option Code
Standard
0.5V to 4.5V DC ratiometric	+5V DC nom. ±0.5V	A

Connector/Cable Options

Option	Option Code
Cable	L
Lid with solder pins	U
Lid with boot IP67	T
Cable length - The standard length of cable supplied with a Positek position sensor is 50cm although you can specify any length you require.	Specified in cm after the L e.g. L200 for 200cm cable from axial cable gland (L0 for U option)

shaft Options

Option	Option Code
Plain shaft with flat	N
Tongue with spring clip	P

<+/-0.1% FSO Linearity error (10mm minimum stroke length)

Option Code
Z650

Dimensions

Body Diameter	28.3mm (solder pins option) 30.8mm (cable boot option)
Body Length (to seal face)	23.2mm
Shaft	8mm, OD 4mm
Measurement Range	Any angle from ±15° to ±70°
Independent Linearity	<±0.31% up to 80° at 20°C <±0.1% available on request
Temperature Coefficient	<±0.01%/°C Gain & <±0.01%FS/°C Offset
Resolution	Infinite
Noise	<0.02% FSO
Frequency Response	>10KHz (-3dB)

Output Signal and Output Load

Output Signal	Output Load
0.5 to 4.5 V DC ratiometric	5k Ohms min
Power Supply	+5V DC nom

Temperature Limits

Operating	-40 to +125°C
Storage	-40 to +125°C

Other

EMC Susceptibility	EN 61000-6-2
EMC Radiated	EN 61000-6-3
Vibration	IEC 68-2-6: 10g
Shock	IEC 68-2-29: 40g
MTBF	350,000 hrs 40°C Gf
Sealing	IP67 (boot version)
Electrical Connections	Screened cable with boot or solder pins

Content missing

P501 Miniature Rotary Position Sensor

P500 Rotary Position Sensor

P502 Rotary Position Sensor