P118 Linear Position Sensor

Description

The Positek P118 slim-line linear position sensor with its compact 19 mm diameter stainless steel body is an affordable, durable, accurate position sensor designed for a wide range of industrial applications. It is particularly suitable for OEMs seeking good sensor performance in situations where a small diameter, short-bodied sensor is needed and cost is important. The P118 slim-line linear position sensor is compact and space-efficient, being responsive along almost its entire length, and like all Positek® sensors provides a linear output proportional to displacement.

Each Positek unit is supplied with the output calibrated to the travel required by the customer, from 0-2mm to 0-50mm and with full EMC protection built in.

Overall performance, repeatability and stability are outstanding over a wide temperature range. The sensor is easy to install and set up. Mounting options include body clamps or a stainless steel mounting flange with two 3.2 mm by 30 degree wide slots on a 25 mm pitch. The stainless steel plunger can be supplied free or captive, with female M4 thread, or spring-loaded with a ball end. The P118 also offers a range of mechanical options, environmental sealing is to IP67.

As a leading designer and manufacturer of linear, rotary, tilt and intrinsically safe position sensors, Positek® has the expertise to supply a sensor to suit a wide variety of applications.

Follow us on Facebook

Positek offers a range of options for its standard sensors. Each sensor is manufactured to suit each customer's preferences. If your requirement is outside the options given below, Positek can modify/ redesign a sensor to suit your specific requirement. Standard options are available as below:

Measurement Range

Factory set to any length from 0-2mm to 0-50mm in increments of 1mm. For example, if your application requires 1" (25 mm) measurement, then Positek will manufacture the sensor specifically for this length. The mechanical length and calibration will be set up for 25 mm.

Electronic Options

Output Signal	Supply Input	Option Code
Standard
0.5V to 4.5V DC ratiometric	+5V DC nom. ±0.5V	A
0.5V-4.5V DC	+9-28V DC nom. 24V	G
0.5-9.5V DC	+13-28V DC nom 24V	C

Connector/Cable Options

Option	Option Code
Connector, Axial, IP67, M8 4 pin	J
Cable, Axial, Gland IP67	L
Cable length - The standard length of cable supplied with a Positek position sensor is 50cm although you can specify any length you require.	Specified in cm after the L or I e.g. L200 for 200cm cable from axial cable gland

Mounting Options

Option	Option Code
Front flange mount	N
Body Clamps	P

Plunger Options

Option	Option Code
Spring loaded (extended)	R
Dome end on plunger	T
Non captive plunger (not with options "R" or "T")	V

<+/-0.1% FSO Linearity error (10mm minimum stroke length)

Option Code
Z650

Dimensions

Body Diameter	19mm
Travel	Any stroke from 0-2mm to 0-50mm (e.g. 21mm)
Independent Linearity	<±0.25% at 20°C <±0.1% available on request
Temperature Coefficient	<±0.1%/°C Gain & <±0.1%/FS/°C Offset
Resolution	Infinite
Noise	<0.02% FSO
Frequency Response	>10KHz(-3dB)

Output Signal and Output Load

Output Signal	Output Load
0.5 to 4.5 V DC ratiometric	5k Ohms min
0.5 to 4.5 V DC	5k Ohms min
0.5 to 9.5 V DC ratiometric	5k Ohms min
Supply Current	10 mA Typical 20 mA max

Temperature Limits

Operating	-40 to +125°C (5V input only) -20 to +85°C
Storage	-40 to +125°C

Other

EMC Susceptibility	EN 61000-6-2
EMC Radiated	EN 61000-6-3
Vibration	IEC 68-2-6: 10g
Shock	IEC 68-2-29: 40g
MTBF	350,000 hrs 40°C Gf
Sealing	IP67
Electrical Connections	Screened cable or integral connector

DATA SHEET

BODY CLAMPS

Content missing

P118 Linear Position Sensor

P117 Linear Position Sensor

P133 Linear Position Sensor