S114 Submersible Linear Position Sensor

Description

The Positek S114 submersible linear position sensor 10bar is an affordable, durable, water resistant, high-accuracy position sensor. Derived from the P101, the S114 was designed for underwater marine and off-shore applications where the equipment is submerged, shares many of the desirable features such as compact size.

The S114 submersible linear position sensor, like all Positek® sensors, provides a linear output proportional to displacement. Each unit is supplied with the output calibrated to the travel required by the customer, from 0-5mm to 0-800mm and with full EMC protection built in. The sensor is very robust, the body and push rod being made of stainless steel for long service life and environmental resistance.

Derived from the popular P101, the S114 has been designed for applications where the sensor may be completely submerged in water up to a pressure of 10Bar, but good sensor performance and cost are still important.

This sensor is waterproof to 100m submersion.

Positek’s PIPS® technology (Positek Inductive Position Sensor) is a major advance in displacement sensor design. PIPS®-based displacement transducers have the simplicity of a potentiometer with the life of an LVDT/RVDT. Our LIPS® range are linear sensors, while RIPS® are rotary units and TIPS® are for detecting tilt position.

Follow us on Facebook

Positek offers a range of options for its standard sensors. Each sensor is manufactured to suit each customer's preferences. If your requirement is outside the options given below, Positek can modify/ redesign a sensor to suit your specific requirement. Standard options are available as below:

Measurement Range

Factory set to any length from 0-5mm to 0-800mm in increments of 1mm. For example, if your application requires 10" (254mm) measurement, then Positek will manufacture the sensor specifically for this angular range. The sensor will measure 10° however will still rotate through 254mm.

Electronic Options

Output Signal	Supply Input	Option Code
Standard
0.5V to 4.5V DC ratiometric	+5V DC nom. ±0.5V	A
Buffered
0.5V-4.5V DC	+24V DC nom. +9-28V	G
±0.5V DC	±15V DC nom. ±9-28V	B
0.5-9.5V DC	+24V DC nom. +13-28V	C
±10V DC	±15V DC nom. ±13.5-28V	D
4-20mA (2 wire)	+24V DC nom. +18-28V	E
4-20mA (3 wire sink)	+24V DC nom. +13-28V	F
4-20mA (3 wire source)	+24V DC nom. +13-28V	H

Connector/Cable Options

Option	Option Code
Cable with Axial PG7 gland 10bar	L
Cable with Radial PG7 gland 10bar	I
Cable length - The standard length of cable supplied with a Positek position sensor is 50cm although you can specify any length you require.	Specified in cm after the L or I e.g. L200 for 200cm cable from axial cable gland

Mounting Options

Option	Option Code
M5 Rod eye on body (only with option "I")	N
Body clamps, 1 pair (see drawing)	P
Body clamps, 2 pairs (see drawing)	P2
M5 rod eye on push rod	U

Push Rod Options

Option	Option Code
Spring loaded (extended) (up to 300m stroke - for longer strokes please contact Us)	R
Dome end on push rod (only with option "R")	T
Non captive push rod	V

<+/-0.1% FSO Linearity error (10mm minimum stroke length)

Option Code
Z650

Dimensions

Body Diameter	35mm
Body Length (Axial version)	Travel: Measurement Length + 168mm
Body Length (Radial version)	Measurement Length + 189mm
Push Rod Extension	Measurement Length + 9mm
Push Rod Outside Diameter	9.5mm
Travel	Any stroke from 0-5mm to 0-800mm (e.g. 305mm)
Independent Linearity	<±0.25% up to 450mm <±0.50% over 450mm at 20°C <±0.1% available on request
Temperature Coefficient	<±0.01%/°C Gain & <±0.01%FS/°C Offset
Resolution	Infinite
Noise	<0.02% FSO
Frequency Response	>300Hz (-3dB); 2 wire 4-20mA

Output Signal and Output Load

Output Signal	Output Load
0.5 to 4.5 V DC ratiometric	5k Ohms min
0.5 to 4.5 V DC	5k Ohms min
± 5V DC	5k Ohms min
± 10V DC	5k Ohms min
0.5 to 9.5 V DC	5k Ohms min
4 to 20mA (2 wire)	300 Ohms max at 24V
4 to 20mA (3 wire sink)	950 Ohms max at 24V
4 to 20mA (3 wire source)	300 Ohms max at 24V
Supply Current	12 mA Typical 20 mA max (voltage versions)

Temperature Limits

Operating	-40 to +125°C (5V input only) -20 to +85°C
Storage	-40 to +125°C

Other

EMC Susceptibility	EN 61000-6-2
EMC Radiated	EN 61000-6-3
Vibration	IEC 68-2-6: 10g
Shock	IEC 68-2-29: 40g
MTBF	350,000 hrs 40°C Gf
Sealing	IP68 10bar (For 350bar sealing see S125)
Electrical Connections	Screened cable or integral connector

Content missing

S114 Submersible Linear Position Sensor

P603 Large Angle Tilt Sensor

S115 Submersible Linear Position Sensor